RepRap 3d Hardware

  Here you find mechanical and electronic devices you need to build your own 3D printer like:

  • Printercontrols: Arduino 2560 + RAMSP 1.4, RUMBA
  • LCD displays
  • Stepper motor drivers
  • Stepper motors
  Here you find mechanical and electronic devices you need to build your own 3D printer like: Printercontrols: Arduino 2560 + RAMSP 1.4, RUMBA LCD displays Stepper motor drivers... read more »
Close window
RepRap 3d Hardware

  Here you find mechanical and electronic devices you need to build your own 3D printer like:

  • Printercontrols: Arduino 2560 + RAMSP 1.4, RUMBA
  • LCD displays
  • Stepper motor drivers
  • Stepper motors
Close filters
 
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
from to
1 From 5
No results were found for the filter!
RepRap RUMBA Board & 6x DRV8825 & Cabling
RepRap RUMBA Board & 6x DRV8825 & Cabling
RepRap RUMBA controller board with 6x DRV8825 stepper motor drivers assembled. Driving up to 6 stepper motors Driving up to 3 extruders Driving LCD displays with SD card reader Stepper motor microstepping configurable down to 1/32 step...
€109.50 *
RUMBA RepRap Controller (board only)
RUMBA RepRap Controller (board only)
RUMBA controller board (board only) This offer is especially for people willing to upgrade their existing 3d printer with this powerfull controller board. Technical data: Driving up to 6 stepper motors Driving up to 2 extruders Driving...
€79.90 *
Hexagon Hotend Set for 3mm Filament
Hexagon Hotend Set for 3mm Filament
Hexagon Hotend Set for 3mm Filament The Hexagon Hotend set for 3mm is the ideal supplemental for your RepRap 3d printer like Mendel, Prusa, Ordbot Hadron, sparkcube or similars. Product content: 1x Hexagon hotend for 3mm filament 1x...
€46.95 *
In stock
Bulldog Extruder XL for 3mm and 1.75mm filament
Bulldog Extruder XL for 3mm and 1.75mm filament
Bulldog Extruder XL for 3mm and 1,75mm Filament symetric design (you can mount motor motor left or right side) additional 6mm inner screw thread fully assembled and tested full metal extruder grove mount compatible hotend holder stable...
€134.90 *
In stock
Hotend Heater Cartridge 12V 40W
Hotend Heater Cartridge 12V 40W
RepRap hotend heater cartrigde 12V ~40W Heater cartridge for RepRap hotends, 12V, around 40W power Dimensions 6mm diameter 20mm length around 1m wires
€3.90 *
In stock
Arduino Mega 2560 R3 (clone)
Arduino Mega 2560 R3 (clone)
Arduino Mega 2560 R3 Board (clone) The Arduino Mega is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16...
€18.95 *
In stock
Full Graphic Smart Controller (with cabling)
Full Graphic Smart Controller (with cabling)
Full Graphic Smart Controller with a 128x64px dot matrix. This display enables you to acces the menu of the 3d printer firmware to control the function of the printer. With the SD card reader you can load gcode data from a SD card and...
€29.50 *
In stock
RepRap RAMPS 1.4 Arduino Shield
RepRap RAMPS 1.4 Arduino Shield
RepRap RAMPS 1.4 Arduino Shield RAMPS is short for RepRap Arduino Mega Pololu Shield. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with its powerful...
€14.90 *
In stock
Mechanical Endstop with cabling
Mechanical Endstop with cabling
Mechanical Endstop with cabling Mechanical endstop and wirings. The cable has a length of approx. 70cm.
€3.50 *
In stock
Optical Endstop with cable
Optical Endstop with cable
Opto Endstop with wiring At least 3 endstops are needed for a 3d printer. The endstop is needed for calibrating the printer when a printjob starts. The set contains the optical sensor and a cable with around 70cm length for connecting...
€3.95 *
In stock
RRD Hall-Endstop
RRD Hall-Endstop
RRD Hall-Endstop with 2 magnets The Hall Endstop enables an easy inductive detection of the endstop position of your 3D printer. When assembling the magnet at your printer you must take care of the magnet polarity! The hall sensor only...
€8.50 *
In stock
Stepper motor driver board DRV8825
Stepper motor driver board DRV8825
DRV8825 stepper motor driver board (pin compatible to pololulu) with heat sink This driver board can be used on 3d printer controler boards like RAMPS 1.4 or RUMBA. The board is pin compatible to the pololulu items. The maximum motor...
€4.95 *
In stock
1 From 5
Viewed