Close filters
  •  
  •  
  •  
  •  
  •  
  •  
from to
1 From 2
No results were found for the filter!
SSR Relais DC / DC Steuerspannung 3-32V DC 40A
SSR Relais DC / DC Steuerspannung 3-32V DC 40A
Solid State Relais (SSR) DC/DC, Steuerspannung 3-32V DC 40A
€26.30 *
Arduino Mega 2560 & RAMPS 1.4 & 5x DRV8825
Arduino Mega 2560 & RAMPS 1.4 & 5x DRV8825
RepRap electronic for controlling a RapRap printer with the following components: 1x Arduino Mega 2560 rev. 3, powerrange 8 - 15V 1x RAMPS 1.4 5x DRV8825 stepper motor driver 5x cooler & cooler pad Cabling set (2 x 2 Pin, 2x 3 Pin, 5 x 4...
€74.90 *
RepRap RUMBA Board & 6x DRV8825 & Cabling
RepRap RUMBA Board & 6x DRV8825 & Cabling
RepRap RUMBA controller board with 6x DRV8825 stepper motor drivers assembled. Driving up to 6 stepper motors Driving up to 3 extruders Driving LCD displays with SD card reader Stepper motor microstepping configurable down to 1/32 step...
€109.50 *
Full Graphic Smart Controller (with cabling)
Full Graphic Smart Controller (with cabling)
Full Graphic Smart Controller with a 128x64px dot matrix. This display enables you to acces the menu of the 3d printer firmware to control the function of the printer. With the SD card reader you can load gcode data from a SD card and...
€29.50 *
Stepper motor driver board DRV8825
Stepper motor driver board DRV8825
DRV8825 stepper motor driver board (pin compatible to pololulu) with heat sink This driver board can be used on 3d printer controler boards like RAMPS 1.4 or RUMBA. The board is pin compatible to the pololulu items. The maximum motor...
€4.95 *
Mechanical Endstop with cabling
Mechanical Endstop with cabling
Mechanical Endstop with cabling Mechanical endstop and wirings. The cable has a length of approx. 70cm.
€3.50 *
Optical Endstop with cable
Optical Endstop with cable
Opto Endstop with wiring At least 3 endstops are needed for a 3d printer. The endstop is needed for calibrating the printer when a printjob starts. The set contains the optical sensor and a cable with around 70cm length for connecting...
€3.95 *
Arduino Mega 2560 R3 (clone)
Arduino Mega 2560 R3 (clone)
Arduino Mega 2560 R3 Board (clone) The Arduino Mega is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16...
€18.95 *
RepRap RAMPS 1.4 Arduino Shield
RepRap RAMPS 1.4 Arduino Shield
RepRap RAMPS 1.4 Arduino Shield RAMPS is short for RepRap Arduino Mega Pololu Shield. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with its powerful...
€14.90 *
RUMBA RepRap Controller (board only)
RUMBA RepRap Controller (board only)
RUMBA controller board (board only) This offer is especially for people willing to upgrade their existing 3d printer with this powerfull controller board. Technical data: Driving up to 6 stepper motors Driving up to 2 extruders Driving...
€79.90 *
14pcs cables complete wiring cables set
14pcs cables complete wiring cables set
14pcs cables complete wiring set The wiring set is ideal for RepRap 3d printers like Mendel, Prusa, OrdBot Hadron or similar models. Each cable has a length of around 70cm and is finished with pin headers. Product contents: 5x 4pin for...
€9.90 *
RepRap Ramps 1.4 Fan Extender
RepRap Ramps 1.4 Fan Extender
RRD Fan Extender for RAMPS 1.4 The RRD Fan Extender for RAMPS 1.4 will be needed if you use your RAMPS 1.4 with Dual-Extruder and all standard outputs D8/D9/D10 are already occupied. Package content: 1x RRD fan extender (assembled and...
€16.90 *
1 From 2
Viewed